深圳市益之源是 专业生产开关电源电源适配器,充电器,工业电源,PSE认证电源,PSE认证充电器的厂家。我们的规格多,品种齐全。产品通过了CE FCC PSE ROHS认证。

以下为PSE认证电源12V1A的电性数:
1、描述(SCOPE):

此承认书适应于EYA1201000型号的适配器。

The purpose of the document is to specify the functional requirements of a 24W switching power supply.

2、输入特性(INPUT CHARACTERISTICS):

2.1输入电压(Input Voltage):

额定电压(Nominal Voltage):100-240Vac

调整范围(Variation Range:90-264Vac

2.2输入频率(Input Frequency:

额定频率(Nominal Frequency:50-60Hz

调整频率(Variation Frequency:47-63Hz

2.3输入电流(Input Current):

当输入交流电压为额定值的下限时,输出电压负载满载,最大输入交流电流1A

2.0Arms max At any input voltage and rated, DC output rated load.

2.4浪涌电流(Inrush Current):

输出额定负载环境温度25℃,输入240Vac冷态起动电源最大浪涌电流小于30A

30Amps Max. Cold start at 240Vac input, with rated load and 25℃ambient.

2.5 AC漏电流(Ac Leakage Current):

当输入电压240Vac时,最大漏电流为0.25mA

0. 25mA Max At 240Vac input.

3、输出特性(OUTPUT CHARACTERISTICS):

3.1输出功率(Power Output);

电压 最小负载 最大负载 峰值电流 输出功率

Voltage Min. Load Max. Load Peak Output Power

+12.0Vdc 0A 1.0A 1.5A 12.0W

3.2负载特性/调整率(Combined Load/Line Regulation):

电压 最小空载电压 最大空载电压 线性调整 负载调整

Voltage Min. Voltage Max. Voltage Line Regulation Load Regulation

+12.0Vdc 11.8V 13.4V ±3% ±5%

3.3波纹和噪音(Ripple And Noise:

测试条件:任何负载正常工作下,使用示波器带宽为20MHz连接到适配器的输出端,同时输出端并连一个4.7uF的电解电容和一个0.1uF的瓷片电容。

The ripple and noise are as follows when measure with Max. Bandwidth of 20MHz and Parallel 4.7uF/0.1uF,crossed connected at testing point.

 

电压 最大波纹最大噪音

Voltage Ripple And Noise(Max.)

+12.0Vdc 120mVp-p

 

3.4启动延迟时间(Turn On Delay Time):

当输入115Vac和输出最大负载时,最大启动时间为2S

2 second Max. At 115Vac input and output Max. Load.

3.5上升时间(Rise Time):

当输入115Vac和输出最大负载时最大时间为40mS

40mS Max. At 115Vac input and output Max. Load.

3.6保持时间(Hold Up Time):

当输入115V和输出最大负载时,最小保持时间为5mS

5mS Min. At 115Vac input and output Max. Load.

3.7效率(Efficiency):

当输入100Vac和输出最大负载时,最小80%

80%Min.At 100Vac input and output Max. Load.

当输入240Vac和输出最大负载时,最小82%

82%Min.At 240Vac input and output Max. Load.

3.8过冲(Overshoot):

在电源开启或关闭的时候,最大15%

15%Max.When power supply at turn on or turn off.

4、保护功能(PROTECTION REQUIREMENT):

4.1短路电路保护:

Short Circuit Protection:

该电源供给器在短路解除时,能恢复正常工作。

The power supply will be auto recovered when short circuit faults remove.

4.2过流保护(Over current Protection):过流故障排除后,电源将自动恢复正常工作。

The power supply will be auto recovered when over current faults remove.

4.3过压保护(Over Voltage Protection)

当输出电压超过额定电压时,电源将保护,故障排除后不能恢复正常工作。

The power supply will not be auto recovered when faults remove.

5、环境要求(ENVIRONMENTAL REQUIREMET):

5.1工作温度(Operating Temperature):

0~ 40,满载,正常工作(Full load Normal operation)

0to40,Full load Normal operation.

5.2储存温度(Storage Temperature):-20to85,带外壳(With package).

5.3工作湿度(Relative Humidity):

5%(0)90%(40),72小时,满载,正常工作

5%(0)90%(40)RH,72Hrs,Full load Normal operating.

5.4振动(Vibration):

1、测试标准:国际电工电子委员会 Operating: IEC 721-3-3 3M3

59Hz,A=1.5mm 加速度(9200Hz,Acceleration 5m/s2) 2、运输(Transportation): IEC 721-3-2 2M2

5-9HzA=3.5mm

9200Hz,加速度Acceleration=5m/S2

200500HZ,加速度Acceleration=15m/S2

3、轴向振动(Axes,10 cycles per axis.

在测试过程中不能出现永久性的损坏。

No permanent damage may occur during testing.

在电源开启和关闭后,样机能够恢复到最初条件。

The product has to restors its original situation after power off/on.)

5.5跌落试验(Dropping)(Packed):

一个角,三个棱, 六个面。

1 corner,3 edges, and 6 surfaces

高度76cm Height:76cm

6、安全及EMC要求(SAFETY AND EMC REQUIREMENT):

6.1安全:符合CE,PSE认证标准。

6.2高压(DIELECTRIC STRENGTH):(测试方法按下面接线图)

()Primary to secondary)3000Vac/5mA/60s.

7、结构参数(MECHANICAL REQUIREMENT)

7.1外壳(Enclosure):

外壳尺寸:74MM*38MM*48MM

The power supply size : 74MM*38MM*48MM

7.2输入座(Input Connector):

日规输入座

7.3;输出线

DC 线: AWM 2464 20AWG*2C,VW-1,80,FT1,300V,线上有字,1.2米,不带环,

DC头为5.5X2.1X10mm音叉内正外负。

DC cable: AWM 2464 20AWG*2CVW-180℃,FT1300Vwith word on

the cord,Length:1.2M, with magnetic ring ,DC plug 5.5X2.1X10mm.in+/out-

8、铭牌 (Label):

可以按客户要求


相关图片资料可参照: http://www.szeya.com.cn/12v1a-japan-pse-certified-power-adapter-through-japan-jet-certification.html

关于PSE认证的介绍请点击:PSE认证电源-益之源对PSE认证电源介绍

证书查询请点击: PSE认证电源证书查询方式及认证号码验证真伪

日期:2012-07-31, 固定链接: http://www.szeya.com.cn/12v1a-pse-power-supply-2.html