120W顶面图

本规格书适应于EYA2400416型号的开关电源.

The purpose of the document is to specify the functional requirements of a 100W Switching Power Supply.

2.输入特性/INPUT SHARACTERISTICS:

2.1 输入电压/Input Voltage; 额定电压/Rated? Voltage:100-240Vac

调整范围?? Variation? /Range:90-264Vac

2.2输入频率/Input Frequency: 额定频率/Reted? Frequency;50/60Hz 调整频率/Variation? Frequency:47-63Hz

2.3 输入电流/Input Current:

当输入交流电压为额定值的下限电压负载满载时,最大 输入交流电 流1.3A

1.3Amps max At any input voltage and rated,AC output rated load

2.4 浪涌电流/Input Current:

当输出为额定负载,环境温度为25 ℃ ,输入240Vac? 冷态 起机时的最? 大浪涌电流小于为20A.

20Amps MAX,cold start at240vac input ,with rated load? and? 25? C? ambient.

2.5 AC漏电流/Ac Leakage Current:

当输入电压240VAC时,最大漏电流为0.25mA.

0.25mA Max At 240Vac input

3.输出特性/OUTPUT CHARACTERISTICS:

3.1输出功率/Power ouptut

电压Voltage?? 最小负载Min Load??? 额定负载Peak?? 输出功率Output Power
24VDC??????????????? 0.01A?????????????????????????????? 4.16A????????????????? 100W

3.2负载特性,调整率/Combined Load/Line Regulation
电压??????? 最小负???? 额定负载????????? 电压范围????????????????? 线性调整
Voltage? Min Load?? Rated.Load????? Voltage Range?? Line Regulation
24VDC?????? 0.01A????????? 4.16A????????????? 5%????????????????????????? +-5%

3.3纹波和噪音 Ripple and Noise:

测试条件:在额定电压及额定条件下,使用示波器(限制带宽为20MHz)连接 到 工业电源的输出端,同时输出端并联一个47UF的电解电容和一个0.1UF的瓷片 电容.

Under miminal voltage and nominal load,the ripple and noise are as follow when measure with Max,Bandwiddth of 20MHz and parallel 47uf/0.1uf,crossed conected at testing point

电压/ Voltage??? 最大纹波/最大噪音/ Ripple? and? Noise(Max)

+24Vdc ? ? ? ? ? ? ?? ≤300 mVP-P

3.4启动延迟时间/ Turn on delay time:

当输入115Vac和输出最大负载时,最大启动时间为2S

2second Max,at 115Vac input and output Max,load

3.5上升时间/ Rise time:

当输入115Vac和输出最大负载时早大时间为40MS

40 Ms Max,at 115vac input and output Max,load

3.6保持时间/ Hold up time:

当输入115Vac和输出最大负载时,最小保持时间为5mS

5ms Max,at 115Vac input and output Max,load

3.7效率/Efficiency:

当输入240Vac和输出最大负载时,最小85%

85% Min? at? 240Vac? input? and? output? Max,Load

3.8过冲/Overshoot:

在电源开启或关闭的时候,最大15%.

15% Max,When power supply at turn or turn off.

4.保护功能/ Protetion function:

4.1短路电路保护/ Short circuit protection:

该电源供给器在短路解除时能正常工作恢复

The? power? supply? will? be? auto? recoverde? when? short? circuit faults remove

4.2过流保护/Over current Protection: 过流故障排除后,电源将自动恢复正常工作.

The power supply will be autorecovered when over current faults remove.

4.3过压保护? /Over? voltage? protection:

当输出电压超过额定电压的150%-180%时,电源将保护,故障排除后 能恢复 正常工作.

The power supply will auto recovered when faults remove 150%-180%

5.环境要求 /ENVIRONMENTAL? REQUIREMET:

5.1工作温度?? /Operating? temperature:

0℃- 40 ℃满, 载,正常工作

0℃to40 ℃,Full toad normal operation.

5 . 2储藏温度/ Storrage temperature: – 20 ℃ to80 ℃

带外壳/with? package

5 . 3工作湿度/Relative? Humidity

5 %( 0℃-) 90 %( 40 ℃,)

5 %( 0℃-) 90 %( 40 ℃)RH ,

5 . 4振动/ Vibration:

1.测试标准:国家电工电子委员会

Operating: IEC 721 – 3 – 3 3M3

5 – 9Hz , A= 1 . 5mm

加速度( 9 – 200Hz , Acceleration 5m / S2 )

5.5运输/ Transportation:

IEC 721 – 3 – 2 2M2

5 – 9Hz A= 3 . 5mm

5.6轴向振动/Axes cycles per axis

在测试过程中不能出现永久性的损坏

No permanent damage may occur during testing

5.7跌落试验/Dropping Packed: 一个角,三个棱,六个面

1corner 3edges and 6 surfaces

高度? 30cm/Height:30cm

6.安全及EMI要求/SAFETY AND EMI REQUIREMENT:

6.1高压/DIELECTRIC STRENGTH HI-POT:

I/P-O/P: 1.5KV/3mA/10S? for? type? tesst

I/P-FG: 1.5KV/3mA/10S? for? type? tesst

O/P-FG: 0.5KV/3mA/10S? for? type? tesst

6.2绝缘抗阻/ Iusulation resistance:

初级对次级/? Primary to secndary: 10MΩ min? at? 500VDC

7.结构参数/MECHANICAL REQUIREMENT:

7.1外壳/ Enclosure:

外壳尺寸:L? X? W? X? H=143mmX60mmX40mm

The power supply size: L X W X H=143mmX60mmX40mm

日期:2012-06-07, 固定链接: http://www.szeya.com.cn/industrial-power-supply-24v4-16a100w-security-and-power-with-ce-certified-power-supplies-high-quality-power-supply.html